Diferencia entre revisiones de «Adaptar Altavoces SonyEricsson MPS-60 para Iphone 4S»
Sin resumen de edición |
Sin resumen de edición |
||
| Línea 19: | Línea 19: | ||
Probar esto:<br/> | Probar esto:<br/> | ||
Pin 11 should have a 1K resistor between it and pin 21, and also a jumper wire from pin 11's end of the resistor to Pin 30 of the dock. I've been using this for awhile and it works fine.<br/> | Pin 11 should have a 1K resistor between it and pin 21, and also a jumper wire from pin 11's end of the resistor to Pin 30 of the dock. I've been using this for awhile and it works fine.<br/> | ||
<br/> | |||
actually from pin 21-1/2/30 is 357K, 21-11 is 11.65M.<br/> | |||
<br/> | |||
11 go ground 1/2/15/16/30 I'm not sure which it would be connected to, but I'm hoping for a short on these. | |||
they're all measured around 11.25M.<br/> | |||
<br/> | |||
Pins 1,2,15,16,29 and 30 are all "ground", they are all connected to the same trace inside the ipod/iphone, so you can use any of them for ground.<br/> | |||
<br/> | |||
pin21 to common = 375k<br/> | |||
pin11 to common = 11.25M<br/> | |||
pin21 to pin 11 = 11.65M<br/> | |||
<br/> | |||
anyway, I found this "thread" (it's really only one post) and he says his bluetooth audio adapter that I will assume is "iPhone certified" had a 95k resistance between the accessory pin (21) and ground.<br/> | |||
<br/> | |||
<br/> | |||
No se puede controlar el volumen cuando esta conectado a los altavoces<br/> | |||
Juaquin, I think the lineout of these devices is meant to be controlled by an amp/receiver/whatever. On the IPhone dock's lineout, the volume cannot be controlled by the phone. This is because of the expectation that an amp will be hooked up. You could always just put a volume control of your own on there (sliding variable resistor like some headphones have?).<br/> | |||
<br/> | |||
<br/> | |||
Connect pins 1, 15 and 21 to pin 11. Use 2, 3 and 4 for line out.<br/> | |||
<br/> | |||
I checked my iPod nano 1G, iPod 3G, iPod 4G click wheel, iPod 4G photo and iPhone 2G. They all have continuity between pins 1, 2, 15, 16, 29 and 30. I think it's safe to say the rest of the iPod and iPhone models follow the same scheme, but if you want to be a real stickler, you can check it out yourself.<br/> | |||
Revisión del 09:28 9 oct 2012
Diagrama conectores altavoces MPS-60
Pinout Iphone
Diseño nueva placa
Conversor 3.3v a 5v
Conector corriente iphone
Volumen?
Concetor a iphone
Tareas actuales:
Solucionar tema volumen controlado desde iphone
http://www.head-fi.org/t/308093/does-anyone-have-the-iphone-lod-pinout
http://www.head-fi.org/t/611590/help-for-lod-pinout-to-iphone-4
Enlaces convertidores dc-dc
http://www.forosdeelectronica.com/proyectos/convertidor-dc-dc.htm
http://www.aaroncake.net/Circuits/6-12conv.asp
Probar esto:
Pin 11 should have a 1K resistor between it and pin 21, and also a jumper wire from pin 11's end of the resistor to Pin 30 of the dock. I've been using this for awhile and it works fine.
actually from pin 21-1/2/30 is 357K, 21-11 is 11.65M.
11 go ground 1/2/15/16/30 I'm not sure which it would be connected to, but I'm hoping for a short on these.
they're all measured around 11.25M.
Pins 1,2,15,16,29 and 30 are all "ground", they are all connected to the same trace inside the ipod/iphone, so you can use any of them for ground.
pin21 to common = 375k
pin11 to common = 11.25M
pin21 to pin 11 = 11.65M
anyway, I found this "thread" (it's really only one post) and he says his bluetooth audio adapter that I will assume is "iPhone certified" had a 95k resistance between the accessory pin (21) and ground.
No se puede controlar el volumen cuando esta conectado a los altavoces
Juaquin, I think the lineout of these devices is meant to be controlled by an amp/receiver/whatever. On the IPhone dock's lineout, the volume cannot be controlled by the phone. This is because of the expectation that an amp will be hooked up. You could always just put a volume control of your own on there (sliding variable resistor like some headphones have?).
Connect pins 1, 15 and 21 to pin 11. Use 2, 3 and 4 for line out.
I checked my iPod nano 1G, iPod 3G, iPod 4G click wheel, iPod 4G photo and iPhone 2G. They all have continuity between pins 1, 2, 15, 16, 29 and 30. I think it's safe to say the rest of the iPod and iPhone models follow the same scheme, but if you want to be a real stickler, you can check it out yourself.